FXO FXS ASTRISK Card

Product Details:

Specifications


OpenVox A800 Series can be used for connecting analog telephones and analog POTS lines through a PC. It supports combinations of FXS and/or FXO modules for a total of 8 lines.
OpenVox A800 Series delivers great voice quality in the telephony systems. With interchangeable FXS/FXO modules, it can eliminate the requirement for separate channel banks or access gateways.
The A800 Series contains 8 module banks. Each bank supports one analog interface. The module banks may be filled with up to 8 FXO or FXS modules enabling the creation of any combination of ports. Scaling of an analog card solution is accomplished by simply adding additional cards.
A800 Series works with Asterisk®, Elastix®, FreeSWITCH(TM), PBX in a Flash, trixbox®, Yate(TM) and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.
Target Applications

• Channel Bank Replacement / Alternative
• Small Office Home Office (SOHO) applications
• Small and Medium Business (SMB) applications
• Gateway Termination to analog telephones/lines

Technical Specifications

• Up to 8 ports through a combination of FXS and FXO modules
• 8 RJ-11 interfaces on a single PCI bracket
• Firmware accelerate I/O access to achieve high stability
• Operating Systems
• Linux (all versions, releases and distributions from 1.0 up)

Minimum Hardware Requirement

• 800-Mhz Pentium III
• 128MB RAM

Certifications

• RoHS Compliant
• Certificates FCC, CE and LVD
• Certified by trixbox CE and Elastix

Features

• Caller ID and Call Waiting Caller ID
• ADSI Telephones
• Loopstart Signaling Support
• Up to 8 Simultaneous PSTN Calls (Per PCIe Slot)
• Interchangeable FXS and FXO modules

Product Details:

Specifications


OpenVox D830 Series is now the leading 8 port T1/E1/J1 PCI-E card in the open source industry. It supports up to 256 channels in E1 mode or 192 channels in T1/J1 modes.
The D830 Series supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. DE830E is supposed to be the most advanced 8 port T1/E1/J1 asterisk® card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.
D830 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.
D830 Series works with Asterisk®, Elastix®, FreeSWITCH®, PBX in a Flash, trixbox®, Yate® and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.
Target Applications

• Voice-over Internet Protocol (VoIP) Services
• Complex IVR Trees
• "Meet-Me" Bridge Conferencing
• Calling Card Platforms
• VoIP Gateways (support SIP, H.323, and IAX)
• Legacy PBX/IVR Services
• Voice/Data Router (replace expensive routers)
• PRI/Switch Compatibility - Network or CPE

Technical Specifications

• 8 T1/E1/J1 ports with PCI-E interface for high performance voice and data applications
• RJ48 connector
• FPGA design, upgradeable firmware onsite
• Power 3.6W Minimum, 4.9W Maximum at 3.3 V or 5 V.
• Operation temperature 0 DegreeC to 50 DegreeC
• Dimension 2U Form factor 12*6.4*1.8cm

Minimum Hardware Requirement

• 800-Mhz Pentium III
• 128MB RAM

Certifications

• RoHS Compliant
• Certificates FCC, CE and CS-03

PRI Switch Compatibility

• EuroISDN (PRI or PRA) - Q.931/Q.921
• Network or CPE
• AT&T 4ESS
• National ISDN 2
• CAS Voice Modes
• DMS 100
• Lucent 5E

Optional Octasic® DSP Echo Cancellation Module-EC2128

• 128ms tail/channel (on all channel densities)
• Octasic® Music Protection
• Adaptive Noise Reduction
• Automatic Level Control (G.169)
• Field upgradeable algorithm
• V.25 / V.8 answer tone (w/ and w/o phase reversal)
• DTMF as per Q.24
• No CPU load as a result of echo cancellation.
• Does not increase the physical size of the card, and no additional slot is required
• EC2128 power 0.33W/3.5W
• Operation temperature 0 to 50 DegreeC

Operating Systems

• Linux all versions, releases and distributions in 1.0 up

Features

• Industry 1st adjustable interrupt routing design
• Interrupts frequency adjustment
• Compatible with All Commercially Available Motherboards
• 8 T1/E1/J1 ports with PCI-E interface for high performance voice and data applications
• Octasic® Hardware Echo Cancellation Module Available