AKOM Technologies Private Limited

Specifications

 D130 Series is now the leading single port T1/E1/J1 PCI-E card in the open source industry. It supports up to 32 channels in E1 mode or 24 channels in T1/J1 modes. It takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.

The D130 Series is an upgrade product of the D115 Series. It''s supposed to be the most advanced single port T1/E1/J1 asterisk® card with superior quality in the open source community. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number

D130 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.

D130 Series works with Asterisk®, Elastix®, FreeSWITCH(TM), PBX in a Flash, trixbox®, Yate(TM) and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

Voice-over Internet Protocol (VoIP) Services

Complex IVR Trees

"Meet-Me" Bridge Conferencing

Calling Card Platforms

VoIP Gateways (support SIP, H.323, and IAX)

Legacy PBX/IVR Services

Voice/Data Router (replace expensive routers)

PRI/Switch Compatibility - Network or CPE

Optional Octasic® DSP Echo Cancellation Module--EC2032

128ms tail/channel (on all channel densities)

Octasic®  Music Protection

Adaptive Noise Reduction

Automatic Level Control (G.169)

Field upgradeable algorithm

V.25 / V.8 answer tone (w/ and w/o phase reversal)

DTMF as per Q.24

No CPU load as a result of echo cancellation.

Does not increase the physical size of the card, and no additional slot is required

EC2032 power 3.83W

Storage temperature -40 DegreeC to 75 DegreeC

Operating Systems

Linux (all versions, releases and distributions from 1.0 up)

Technical Specifications

Single T1/E1/J1 ports with PCI interface for high performance voice and data applications

RJ48 connector

Low profile option

FPGA design, upgradeable firmware onsite3

Minimum Hardware Requirement

800-Mhz Pentium III

128MB RAM

PRI Switch Compatibility

EuroISDN (PRI or PRA) - Q.931/Q.921

Network or CPE

AT&T 4ESS

National ISDN 2

CAS Voice Modes

DMS 100

Lucent 5E

Features

Industry 1st adjustable interrupt routing design

Interrupts frequency adjustment

Compatible with All Commercially Available Motherboards

Octasic® Hardware Echo Cancellation Module Available

Single T1/E1/J1 ports with PCI interface for high performance voice and data applications

Specifications

OpenVox D430 Series is now the leading 4 port T1/E1/J1 PCI-E card in the open source industry. It takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.
The D430 Series is an upgrade product of the D410 Series. It''''s supposed to be the most advanced 4 port T1/E1/J1 asterisk® card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.
D430 Series offers an on-board Octasic® DSP-based echo cancellation module. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 128 channels in E1 mode or 96 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.

D430 Series works with Asterisk®, Elastix®, FreeSWITCH(TM), PBX in a Flash, trixbox®, Yate(TM) and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

Voice-over Internet Protocol (VoIP) Services

Complex IVR Trees

"Meet-Me" Bridge Conferencing

Calling Card Platforms

VoIP Gateways (support SIP, H.323, and IAX)

Legacy PBX/IVR Services

Voice/Data Router (replace expensive routers)

PRI/Switch Compatibility - Network or CPE

Technical Specifications

4 T1/E1/J1 ports with PCI interface for high performance voice and data applications

RJ48 connector

FPGA design, upgradeable firmware onsite

Power 2.6W Minimum, 3.9W Maximum at 3.3 V or 5 V.

Operation temperature 0 DegreeC to 50 DegreeC

Dimension 2U Form factor 12*6.4*1.8cm

Minimum Hardware Requirement

800-Mhz Pentium III

128MB

PRI Switch Compatibility

EuroISDN (PRI or PRA) - Q.931/Q.921

Optional Octasic® DSP Echo Cancellation Module-EC2128

128ms tail/channel (on all channel densities)

Octasic® Music Protection

Adaptive Noise Reduction

Automatic Level Control (G.169)

Field upgradeable algorithm

V.25 / V.8 answer tone (w/ and w/o phase reversal)

DTMF as per Q.24

No CPU load as a result of echo cancellation.

Does not increase the physical size of the card, and no additional slot is required

EC2128 power 0.33W/3.5W

Operation temperature 0 to 50 DegreeC

Features

Industry 1st adjustable interrupt routing design

Interrupts frequency adjustment

Compatible with All Commercially Available Motherboards

4 T1/E1/J1 ports with PCI interface for high performance voice and data applications

Octasic® Hardware Echo Cancellation Module Available

Minimum order quantity: 1 Piece

Specifications
OpenVox D230 Series is now the leading 2 port T1/E1/J1 PCI-E card in the open source industry. It takes full advantage of Octasic?? Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.
D230 Series is an upgrade product of the D210 Series. It''''s supposed to be the most advanced 2 port T1/E1/J1 asterisk?? card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.
D230 Series offers an on-board Octasic?? DSP-based echo cancellation module. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The Octasic?? DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 64 channels in E1 mode or 48 channels in T1/J1 modes. Further, this module takes advantage of the Octasic?? Voice Quality Enhancement to provide superior sound quality on all calls.
Target Applications
Voice-over Internet Protocol (VoIP) Services
Complex IVR Trees
"Meet-Me" Bridge Conferencing
Calling Card Platforms
VoIP Gateways (support SIP, H.323, and IAX)
Legacy PBX/IVR Services
Voice/Data Router (replace expensive routers)
PRI/Switch Compatibility - Network or CPE
Minimum Hardware Requirement
800-Mhz Pentium III
128MB RAM

Operating Systems
Linux (all versions, releases and distributions f rom 1.0 up)

Technical Specifications
2 T1/E1/J1 ports with PCI interface for high performance voice and data applications
RJ48 connector
FPGA design, upgradeable firmware onsite
Power 2.3W Minimum, 3.5W Maximum at 3.3 V or 5 V.
Operation temperature 0 DegreeC to 50 DegreeC
Dimension 2U Form factor 12*6.4*1.8cm

Optional Octasic?? DSP Echo Cancellation Module-EC2064
128ms tail/channel (on all channel densities)
Octasic?? Music Protection
Adaptive Noise Reduction
Automatic Level Control (G.169)
Field upgradeable algorithm
V.25 / V.8 answer tone (w/ and w/o phase reversal)
DTMF as per Q.24
No CPU load as a result of echo cancellation.
Does not increase the physical size of the card, and no additional slot is required
EC2064 power 0.33W/3.5W
Storage temperature -40 DegreeC to 75 DegreeC
PRI Switch Compatibility
 
EuroISDN (PRI or PRA) - Q.931/Q.921
Network or CPE
AT&T 4ESS
National ISDN 2
CAS Voice Modes
DMS 100
Lucent 5E
Certifications
RoHS Compliant
Certificates FCC, CE and CS-03